- VIA TECHNOLOGIES INC VT8378 S3 UNICHROME GRAPHICS ADAPTER INSTALL
- VIA TECHNOLOGIES INC VT8378 S3 UNICHROME GRAPHICS ADAPTER DRIVER
Unichrome igp km400 kn400 need a new Graphic Card because mine has no visual effects. Performance is to me that will need the first.
VIA TECHNOLOGIES INC VT8378 S3 UNICHROME GRAPHICS ADAPTER DRIVER
The connector can be seen in the photo of the main circuit board just below the lower heatsink.Download Now KM400 UNICHROME GRAPHICS DRIVERĭistro Kubuntu Downldoad free driver updates for VIA/S3G Unichrome igp km400 kn400 also known as, VIA/ S3G UniChrome Graphics, VIA/S3G UniChrome IGP for Windows XP 32 bit. This connector - referred to as a 'connectivity foot' or 'connectivity bar' - which providesĪ way of adding additional legacy ports. On the underside of the unit (if mounted vertically) is a 44-pin plug. However, if I replace the Microdrive with a Compact Flash card I get: With just the hard disk plugged in I get: I installed a jumper on the IDE drive to configure it as a slave drive. I decided the easiest way to do this was from a hard disk plugged into the IDE connector.
VIA TECHNOLOGIES INC VT8378 S3 UNICHROME GRAPHICS ADAPTER INSTALL
I wanted to install some software on a Hitachi Microdrive There appears to be a small quirk with the M300C (or a Hitachi Microdrive). The former had 4 chips per side whilst the latter had 8 chips per side. I found a Samsung 1GB part M70T2864QZ3 only appeared as 512MB whilst another Samsung 1GB part M470T2953EZ3Ĭorrectly appeared as 1GB. Is labelled: 512MB DDR2 PC533 520230-0704 and is manufactured by Transcend. RAM: There is a single 200-pin DDR2 SODIMM socket for the RAM. Click on the photo for a larger version.īoth the Flash memory and the RAM in the M300C are easily replaceable.įlash: The standard flash memory is a Compact Flash card plugged into a socket adjacent to a 44-pin I find that the M300C I actually runs at a very modest power consumption of 14~16W. The IGEL M300C uses an external 12V supply with a conventional coaxial type connector.Īlthough the M300C data sheet says it comes with an "48~50W External Power Adapter" VT6102 (rev 78)Ġ1:00.0 VGA compatible controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 60)Ġ0:12.0 Ethernet controller: VIA Technologies, Inc. VT8237 ISA bridge Ġ0:11.5 Multimedia audio controller: VIA Technologies, Inc. USB 2.0 (rev 86)Ġ0:11.0 ISA bridge: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)Ġ0:10.4 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)Ġ0:10.3 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)Ġ0:10.2 USB controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 81)Ġ0:10.1 USB controller: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)Ġ0:10.0 USB controller: VIA Technologies, Inc. VT8237/VX700 PCI BridgeĠ0:0f.0 IDE interface: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host BridgeĠ0:01.0 PCI bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host BridgeĠ0:00.7 Host bridge: VIA Technologies, Inc. PT890 Host BridgeĠ0:00.4 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host BridgeĠ0:00.3 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host BridgeĠ0:00.2 Host bridge: VIA Technologies, Inc. CN700/VN800/P4M800CE/Pro Host BridgeĠ0:00.1 Host bridge: VIA Technologies, Inc. Pge cmov pat clflush acpi mmx fxsr sse sse2 tm nx pni est tm2 xtpr rng rng_en ace ace_en ace2 ace2_enĬlick for the output from the linux lspci command:Ġ0:00.0 Host bridge: VIA Technologies, Inc. (EOL February 2016)įor those to whom it matters here is some detail from Linux's /proc/cpuinfoįpu vme de pse tsc msr pae mce cx8 sep mtrr M320C - New motherboard: VIA Eden X2 1GHz (EOL March 2014).M310C - M300C with a 1GHz CPU (EOL November 2011).The M300C was part of Igel's Universal Desktop range and was theįirst of the UD3 (Generation 2) line of thin clients. Horizontal deployment only supported with optional rubber feet!" "CAUTION: Standard deployment of the device is in vertical position, As can be seen in the photographs my Igel M300C came without any mounting foot.